Fibroblast device uses plasma, an ionized gas between the tip of the Fibroblast tool and patients skin. During the procedure electric arc forms, referred to as a plasma flash or mini lightning. Only surface of the skin is touched causing tissue to retract. This is known as sublimation, the process of turning solid directly to gas. Targeted tissue sublimate, therefore no damage to surrounding areas or deeper skin layers. Patient can resume regular activities right away with minimal discomfort.

Yes. Anyone interested in Fibroblast procedure is required to have face-to-face consultation. Careful assessment by Purebeau specialist will ensure right treatment plan. Multiple factors affect the aging process. Each person and treated area is different and needs to be determined individually. Our goal is to keep clients informed and meet their expectations.

When activated, Fibroblast tool creates plasma flash which travels from the tool’s tip to treated area. The tool itself never touches the skin however plasma flash creates a tiny dot upon the contact. Further points are applied creating a symmetrical grid over the treatment area. This in effect causes tightening of skin fibers. Only surface of the skin is affected and deeper layer known as the basal lamina is not. Fibroblast is non-invasive treatment, no cuts to the skin or stitching is necessary. Fibroblast is completely bloodless and without unnecessary damages to surrounding tissues.

Fibroblast is non-surgical treatment with no pain or minimal discomfort reported by patients. Topical cream is applied to numb treated area prior to procedure. Immediately after the treatment the skin will be reddened and lightly swollen. This will usually last up to 3 days, although slight redness may remain for up to 2 weeks. During the procedure carbon crusts will form on the skin directly where Fibroblast tool was applied. Crusts should not be touched for 5-7 days however post-procedure foundation can be used to camouflage them. Purebeau offers specific Fibroblast Powder in two variations for either lighter or darker skin complexion. To minimize complications you will be informed on proper aftercare following the procedure.

Fibroblast is very safe and side-effects are rare but infection, scarring and temporary change of skin pigmentation may occur. Carbon crusts, a tiny superficial dots which form directly on the skin are part of normal healing process and when correctly treated with after-cream will cause no threat and fall off 5-7 days after treatment. Mild swelling is expected during first 3 days and usually entirely gone by day 5. Majority of our patients do not report any of those after a week.

Yes. It is very important to follow our after care recommendations. Carbon crusts CANNOT be scratched or removed. Drying skin by dabbing with a clean, lint-free cloth is allowed. Purebeau Aftercare balm should be reapplied to the area. Healing skin should be protected from direct sun with SPF50 cream. Sports, swimming and sauna are not permitted until crusts fall off. This should happen within 7 days of procedure.

Most patients should notice the effect of the procedure right away. However the healing will continue and the full result should be visible within 2-4 weeks. In some cases patients may need more then one treatment. This depends on treatment area and skin condition as well as patient’s expectations.

In some cases just one treatment may be sufficient, especially with lighter corrections. Many of the treatments will depend on a size of the treated area and customer’s desired degree of correction. Full effect of the first treatment will be visible after 2-4 weeks following the procedure. If patient requires additional treatment to achieve optimal results those should be scheduled at 6 to 8 weeks intervals. Effectiveness of Fibroblast non-surgical lift is comparable to traditional techniques. In order to evaluate number of required procedures and choosing best treatment plan face-to-face consultation is required.

The treatment should last long term rather then few months although it is hard to predicted exactly. Aging is dynamic process and there are many factors affecting patients individually. Lifestyle, diet and genetics just to mention few. As of today permanent results are not possible, after Fibroblast procedure or traditional surgery your skin will be a subject to aging. Your skin will continue to relax (loosen) again. In some rare situations aging may be accelerated and effectiveness of Fibroblast would be shortened. Purebeau technician will discuss those conditions, so patients have better understanding of what to expect.